PVC windows with double-glazed windows with timely and proper maintenance are able to last 10 or more. But often due to the fact that homeowners practically do not follow them, the service life is reduced several times. One of the aspects of the maintenance of the plastic window is adjustment in different planes, as well as seasonal increase and decrease in the rifle (adjustment of winter-summer).

Want to know how to regulate plastic windows with your own hands? Here we will give instructions for self-adjustment plastic windows and the doors of the rotary and swivel-folding action.

To properly serve and adjust the plastic window, it is necessary, first of all, to know how its mechanical fittings are arranged. Most modern windows, fittings are practically no principles of action and adjustment. Window flaps have adjustable loops, but they have a different device. The upper loop has an adjustment horizontally and allows you to change the imposition, and the bottom - vertically, horizontally and the appraul.

If the window sash is not only opens to the side, but also leans (swivel-inclined design), setting into the ventilation mode, then a slightly different fitness configuration is used. A folding mechanism and special rods are added at the top of the sash that hold it in the crowded position. The window handle in this case does not have two, but three main positions: throw back the sash, open the sash, close the window.

To the window is sealed, its elements are paved with rubber seals. However, these seals cannot provide high tightness if the sash does not fit to the frame exactly.

The adjustment of the GRAY is simple, and can be performed independently. To do this, use the adjustment nodes on the accessories.

Adjustment of plastic windows vertically

The lower hinge loop has a removable plastic cap ( 1 ). It is easily shifted up.

When the cap is removed from above, you can see the adjustment head ( 2 ) With a notch under the hexagon. This head adjustment head of the vertical window. To adjust the window, you will need only one tool - 4 mm hexagon.

This hexagon need to rotate the head for or counterclockwise ( 3 ). In this case, the sash will rise or descend, respectively.

Adjusting plastic windows horizontally

Horizontally sash adjustable and top and bottom loop. If you twist the upper screw ( 4 ) clockwise, then top part The sash will be width in the side of the loop.

Lower loop is adjustable. The screw of its adjustment is at the bottom side. If the loop is located at the very slop, then you can see it in the side, substituting the mirror ( 5 ).

Exactly the same hexagon head available on the other side of the loop ( 6 ).

Adjusting the clamping of the plastic window

The clamp of the flap of the plastic window is regulated by the eccentrics ( 7 ) Located from the handle side, but can also be adjusted by the loop. In swivel-folded windows before adjusting the top loop, you must open the sash, click on the block ( 8 ) And turn the handle to the ventilation mode.

Press the upper loop of the window is adjustable with screw ( 9 ).

Eccentric clay clamps ( 10 ) have a label that indicates which position it is. The closer the label to the room, the stronger the imposition. If you turn the eccentric by the label towards the street, then the flying is weakened.

Services of fittings

Accurate adjustment of the contract is performed before the cold season, when the window tightness is necessary. And for the summer, the eccentrics turn in a label towards the street to provide micro-taking even with a fully closed window. In some types of window accessories, the canopy is adjusted by a bolt located on the side of the handle. In addition, the weakening of the River for the time of the warm season extends the service life of rubber seals. If they are constantly tightly pressed, after a couple of years they will lick and stop ensuring tightness.

In the fall, seals need to be cleaned from dust and dirt with a soapy water and a sponge. They are also helpful to lubricate with liquid silicone oil.

From time to time you need to lubricate and fittings. Experts recommend doing it at least once a year. For lubricating mechanisms, special window oils can be used, consistant and liquid machine oils, as well as aerosol lubricants of type WD-40. It is very important before lubricant to carefully clean the mechanisms from dirt and, if possible, from the old lubricant, which contains many abrasive particles. For applying consistant lubricant, it is convenient to use the syringe. Aerosol and liquid lubricants raise themselves, so the mechanisms have to handle them more often.

The flaps of the plastic window need adjustment when the sagging is noticeable or drafts are felt when closed window noise. When drafts appear, it is worth determining the place of their penetration into the room - if it blows from the window opening, then in this case it is necessary to perform measures to adjust the clamping of the plastic window. If the draft is felt on the side of the loop, then in this case it is necessary to press the loop itself directly.

Vertical adjustment

Windows adjustment with their own vertical hands is performed by manipulation on the bottom mounted loop of the window design. During the adjustment process, you need to open a capped loop cap to open access to the opening for a special hexagon key. If you rotate the hex key clockwise, thus, you can lift the window sash slightly. If the key to rotate counterclockwise, then the sash will fall. Through this manipulation, you can change the location of the window sash vertically about 2mm from its initial position.

Adjusting the clamping of the sash is performed in the event that the window opening is very blowing. These manipulations are performed through the use of special eccentric. They are located, as a rule, around the perimeter of fittings. If you move the eccentric in the direction clockwise - the sash is stronger to the window frame. To weaken the pressed, you need to turn eccentric counterclockwise. The strip, which is located on the eccentric, will prompt the density of the pressed flap to the window frame. So, if this strip is directed from the window seal, then in this embodiment, the clamp is weakened.

Horizontal adjustment

Adjusting the horizontal straight line is performed if you need to slide a slightly frame or eliminate the small sash sash. Such adjustment is performed using the top, and the bottom mounted loop Window design. Holes for the hexagon key are in the hinges. If for adjustment to use the bottom mounted loop, you can perform all the necessary manipulations, both with open and with a plastic window closed. If you rotate the hex key in the lower loop opening clockwise - the bottom window opposite from the loop will be lifted. Well, if the key is rotated counterclockwise, the bottom of the window drops a little. Similar manipulations can be performed with the top edge of the sash, only they can only be executed if the window is open. The possibility of a shift in this way is 2mm from the initial position of the sash.

Repair-window is always ready to offer the service and repair of plastic windows at the highest, professional level. Specially trained specialists quickly and efficiently perform the adjustment of windows from PVC. We can also see the video about the adjustment of plastic windows, if you decide to perform similar manipulations yourself.

The quality and long service life of the input door depends not only on right mounting. Timely adjustment of plastic doors plays not last role. You can perform it yourself using the hex key and knowing the signs indicating the need for configuration.

Signs of the need to set the loops

Initially adjust the door must install when it is installed. Therefore, when taking work, be sure to pay attention to the fact that it is installed smoothly, easily opened and closed, in the open state there should be no spontaneous stroke of the web in one direction or the other. However, over time, additional hinge settings may be required to ensure the correctness of the work. entrance doors. To do this, you can call the wizard or perform it with your own hands.

It is possible to determine the need to adjust windows and doors by conducting such tests:

• Closing the door, between the blade and put the box ordinary sheet Paper. After closing, pulling out and pull out, turning attention to the applied force. It should be done for the entire perimeter, the effort of this should be the same everywhere. If the paper in some place is pulled out easier or harder, it will be a sign of the need to adjust.
• Become from the side, reverse closure and outline the pencil door around the perimeter, using the Lutka as a ruler. Open it and explore the distance from the line to the edge of the canvas. If it is the same on all sides, the setting is not required. Otherwise, you need to adjust the loops.
• Operate the door and leave in that position. It should not be spontaneously open or closed. If this happens, the control of the loops is necessary. When carrying out this test, be sure to exclude the effect of wind and drafts.

There are also obvious signs that will indicate the need to configure the operation of doors and windows.

• The canvas clings to the box, preventing the free move of the door. This problem indicates the need to adjust the loops in the vertical or horizontal plane.
• Violation of tightness. Purpose of cold air with a closed state of the sash indicates the weakening of the clutch and the need to strengthen the fitting of its canvas to the box.
• Plate handles. Over time, the fastening bolts can relax, and the handle will be fused. To eliminate the problem, you need to remove the decorative bar and twisted screws.
• The handle turns with the effort. The reason may be trash caught in the lock mechanism.

Types adjustment

Setting up doors and windows is different in the direction of regulation. She may be:

• vertical;
• horizontal;
• frontal.

With vertical configuration, the loops can be mixed up or down. It is carried out if the door runs about the threshold. In such a situation, they say that the door has saved under its weight. If there are dents on the seal, it is also necessary to adjust the doors vertically.

Horizontal setting of loops moves the canvas to the right or left. It is needed if the door clings for vertical racks over the entire height or only in the area of \u200b\u200bthe castle.

Frontal adjustment of the clamping of doors and windows will adjust the adjacent of the canvas or sash to the box. It is necessarily carried out depending on the time of year. For the winter, clamp is enhanced, and in the spring it is reduced. The weakening of the adjustment in the warm season must be carried out necessarily, because the seal may dismiss and will lead to a violation of the work of the doors.

To configure doors and windows with your own hands, you will need a special key and understanding what needs to be done. At the same time, if you want to shift everything canvas evenly, then all loops are adjusted. If there is a skew, it is eliminated by setting up one of them.

Vertical adjustment instruction

You can adjust the door vertically by using the hex key with a diameter of 4 mm by performing such actions:

Horizontal adjustment instructions

To independently adjust the horizontal, the key will also need. The actions required to configure your own hands:

1. Remove the decorative lining from the loop.
2. using hexagon. Offset to the right occurs when you turn counterclockwise. And on the contrary, turn the key clockwise, the canvas will move to the left.

Frontal adjustment clamp

To regulate the clamping, the hex key is not needed. It is adjusted with pliers or screwdriver by turning the eccentric. They are located on the end around the perimeter of the canvas. You can adjust the clamp by turning those eccentrics where the force of adjustment is insufficient or excessive.

Adjusting the plastic door, made in a timely hand, horizontally, vertical or adjusting the clamp, will extend the service life of the input or balcony doors, as well as plastic windows, and will save from the need to repair.

This question may appear at the owner of any plastic design.

There are several manufacturers of window fittings, it can be trademarks: Roto, Maco, Winkhaus, Siegenia-Aubi, etc. But regardless of the manufacturer of accessories, methods for adjusting plastic windows are about the same and fundamentally different, with the exception of small design features.

And so, by unacceptable manipulations with the fitting of the plastic window, you can adjust:

• horizontally (left-right);
• vertically (up-down);
• on the clamp (window closing density).

Adjusting the flap of the plastic window vertical (up- down)

Change the position of the vertical sash it follows if the window sash when opening and closing clings the frame or locking fitting nodes from below or from above.

You can perform this manipulation by removing the protective cap from the bottom loop, and the hexagon number 4 is twisted (the movement of the sash up) or unscrewed (movement of the folding) adjustment screw, which is in the top of the bottom loop.

Adjusting the plastic window horizontally (left - right)

Change the position of the horizontal flaps should be if the window sash when opening and closing clins the frame or locking fittings nodes on the sides or from below the corners.
And also if the sash is removed from the frame to so much that the safety device mechanism does not enter the response part. In this case, the handle is blocked, and its turn to the ventilation mode becomes impossible.

Change the horizontal position of the sash relative to the frame is both on the upper loop and on the bottom loop of the fittings. The adjustment of the screw, which is located at the bottom of the bottom loop, is performed by hexagon No. 4, and it has sectors for hexagon from two sides. The adjusting element of the top loop can perform in the form of a screw or eccentric (depends on the manufacturer). Adjust the upper loop using hexagon number 4.

Adjusting the safety raising

You should change the tuning of the safety lift if the window does not close or not translated into the ventilation mode due to the fact that the handle does not rotate.

Adjusting the safety climber is performed using the TORX-T15 key, for this, the clamping screw is weakened on the block of the block, the movable element is shown to the required height, after which the screw is delayed.

Adjusting the clamping clause

Change the folding force to the frame to the frame should be if the window in the closed position "sits". Find out this drawback is quite easy. You can bring to the pairing area of \u200b\u200bthe sash and the frame of the lit lighter and on the deviation of the flame to determine the place of drafts, and you can insert the paper between the sash and the frame of the paper and after closing the sash to pull it on yourself. Without an effort, the elongated strip will talk about the absence of clamping sealing seal to the frame.

The force of the clamping force to the frame is regulated by changing the position of the eccentric locking pin, located along the perimeter of the sash, the eccentric roller on the "scissors" of the upper loop. This manipulation is performed with the help of the same hexagon or ordinary passage (depends on the manufacturer of the fittings).

When turning the handles of the eccentrics enter the clamping platforms, so the displacement of the eccentric roller in the direction of increasing the distance from its edge to the central axis of the sash increases the clamp, and its offset in the direction of decreasing this distance - reduces the clamp.

When adjusting the clamp, it should be considered:

• all the eccentrics of the presses must be set to the same position;
• it should not be strongly changed the position of the eccentrics;
• very dense clamp of the sash can lead to premature deterioration of the seal;
• to adjust the eccentric roller on the "scissors" of the upper loop, open the window, click on the safety mechanism lever and turn the handle to the ventilation mode. In this case, the sash will hang on the "scissors" traction and access to the roller will open.

Replacing the Pen Plastic Window

Replace or pull the fastening of the handle of the sash, by turning the circle protective plastic panel. In this case, access to the knob mounting screws.

Lubrication of fittings

You will not fool - you will not go! This folk wisdom should be applied to plastic windows at least once a year. Lubricate all moving elements and locking nodes follow. The moving elements in the places of the guide grooves are lubricated with oil for sewing machines, and the response strips and adjusting pin with technical vaseline or solidol.

Lubrication and replacement of the seal

If, when opening the sash, it makes an unpleasant sound, you can lubricate with silicone lubricant or technical vaseline. Seals are recommended to change once every 10-15 years, it is in this time interval that the sealant loses its elasticity. The replacement is easily performed, the seal is removed from the groove, and in its place, not stretching, a new one is inserted.

Of course, in the event of problems with the functioning of the fittings of the plastic window, you can contact the professionals whose work will have to pay for their blood earned. As a result, a huge desire appears to independently adjust the plastic windows. We can assure you that it is not necessary to have seven spans in the forehead to fulfill this work, as well as possess expensive tools and ingenious devices.

Sections Articles:

Adjusting plastic doors is a process that is designed to eliminate all sorts of problems that appeared during the use of the design. It doesn't matter how the door is the door and its components, the items break always, the more frequently used.

Most often requires the setting of doors, for the reason that the loops can weaken and fall out. As a result, the door stands unevenly, and draft ships blows from the opened slots. The root cause of the breakdown is to wear individual parts, but their quality play a considerable role. That is why it is not necessary to save on the quality so that in the future I did not have to think about adjusting the plastic door.

If you have problems with a plastic door, but you don't want to refer to the masters, you can fix the breakdown yourself. But for this you need to prepare and find out the answers to the following questions:

• In the same place the doors are details for adjustment;
• What problems can arise at all with plastic doors and how to solve them;
• How exactly the adjustment of the plastic door.

What is responsible for adjustment

To configure the door, you will need a hexagon with a diameter of a 4 millimeter (most often), sometimes there will be no clients.

The first adjustment knot can be found on the bottom door loop, scrolling it with a hexagon you can lift or lower the door, depending on the direction of the twist.

Required tool.

Here you can find a node that shifts the bottom of the door to the right or left. Sometimes adjusting screws are honeclined by protective caps that are easy to find and remove. To move to the left or right, the top of the door must be twisted the screw, located at the top loop.

The pressure power of the door to the door box is regulated by the eccentrics, which can be found throughout the body of the door. Twist them, it is possible to achieve accurate adjustment of plastic doors and their tightness, by changing the clips in separate areas. In the doorway with a swivel-folding principle of work there is a way to adjust the clips of the entire top. To do this, scroll the screw located at the top of the door.

It is not easy to get to this screw, you need to put the door immediately and in the ventilation mode and in the "Naraspa" mode. From such a opening protects the built-in mechanism that can be circumvented. Just open the door, align the plate, which is located at the door of the door at the handle (parallel to the seal rubber) and rotate the door handle to the ventilation mode. This is a rather complicated procedure, so in order to know exactly how to adjust the plastic door in this mode, we advise you to get acquainted with the video.

Methods for adjustment with different problems

To correct the flaws, you need to know which screw for what is responsible, and under what problems to turn it.

This is due to the complexity of the design of the door and the abundance of all sorts of screws, the incorrect twist of which can lead to a complete disorder of the mechanism.

On request, the adjustment of plastic doors can be found many videos from professional masters, which will help in work.

Sagging

Over time, the input protection saves under its own weight, and due to the fact that is mounted in the air. This is one of the most common problems and at the same time unpleasant, since in this case the lower profile is running about the frame, and in case of complex cases, the door becomes not easy to close. In this case, we will definitely have to take care of the adjustment of the plastic door until the position was aggravated.

Skot and sagging doors.

To fix this problem, you need to raise the door up. This can be done using a special opening in the middle of the bottom loop. By inserting and tugging the hexagon clockwise, we raise the door higher. If you need to lower the door, you will have to twist counterclockwise.

In the case when the frame is tiled only by the opposite door from the loop, the horizontal regulation of the upper loop will help. By inserting the tool into the hole and turn clockwise, we draw the upper door of the door closer to the frame.

Adjusting the upper loop.

Adjusting plastic doors from sagging can be carried out and independently, but instructions from the manufacturer are required for the purpose of destination of all screws and connectors.

Friction

If, when you close the opening, the door turns about the box, you need to know how to adjust the mechanism, shifting plastic doors to the left or right. First we take the lower part by scrolling the hex key in the slot in the bottom loop, and then we do the same trick from the top.

Bad presser

If there is a drafts from your door, then most likely we will slightly press the door to the box. This is corrected by adjusting the plastic door, namely, the eccentrics. The mechanism of their work is that when closing the eccentric climbs behind the clamping plate.

Eccentric plastic doors.

From this it follows that it is necessary to check each of the connectors to be checked completely equally equally. It is not necessary to believe that the stronger the twist - the more reliably the clamp, with an extremal fit, the sealer can disappear and stop performing its work. Masters recommend weakening clamping in the summer to give a sealing gum a little freedom and provide a small additional ventilation in the house.

Complex closure

Another common problem of plastic doors is to close them, it is necessary to apply force. Most often, power is required to apply when turning the handle.

Such symptoms indicate winter mode of eccentrics, and to facilitate closing you need to weaken the screws.

Before adjusting plastic doors, you need to view a learning video to know the required tightening level.

Another reason for the difficult closure can be a door mechanism zoom. In easy cases you can do with complete lubrication, in difficult situations you will have to disassemble the door and clean the system.

If the door is used for quite a long time, the handle can break. To correct this problem, turn the top plate of the handle base, and tighten the bolts under it.

Adjusting the doors from the GreenEQ loop

If the door has a lot of weight (more than 40 kg) and is often used, it is in most cases equipped with loops of the GreenEQ type. Adjusting plastic doors, and especially independently, it may become a problem, so before starting work it is recommended to view the video of the process. You can regulate in three planes:

• Vertical;
• Horizontal;
• Click to the box.

To access the hinges, it is necessary to remove plastic protection from them, which is quite easy to do. To raise or lowering such a door, insert the hexagon into the connector located at the bottom of the loop and tapping into one of the sides adjust. Remember that the adjustment of plastic doors begins with the bottom loop, and then the average and the top can be adjusted below it, which can be made independently.

To shift the doors to the left-right, you should screw or unscrew the screw located in each loop under the decorative disguise.

Insert the hex key from the end from the end of the hinge, and change the position of each of them in a circle. Now you know how to properly adjust the plastic doors mixed or weakened, using your own hands.

So, the adjustment of the doors from PVC is a simple process, but requiring care and perseverance when implementing with your own hands. Now you know how to adjust the plastic door, without causing specialists to the house.